SENSOR
Refine Search
BALLUFF BES 516-326-S4-C
P/n. BES 516-326-S4-C
M18, PNP-NO, 24VDC, 5 mm Sensing Distance
Flush Mounting, IP68, CuZn Nickel Plated Housing
S4 Connector
BALLUFF BES516-131-S4-C
BALLUFF Inductive Proximity Sensor
P/n. BES516-131-S4-C
M12, 4 Wire, PNP, 24VDC,4mm Sensing Distance
Non Flush Mounting, IP68, Stainless Steel
S4 Connector
BALLUFF BES516-324-G-S49-C
P/n. BES 516-324-G-S49-C
M8, DC - 3 Wires, PNP, NO, 10-30VDC, 2mm Sensing Distance, Flush Mounting, IP68, Stainless Steel, Plug Connection
BALLUFF BKS-S20-10-05
BALLUFFRight Angle 4 Pins M12Connector
BKS-S20-10-05
10...30VDC
2 LED Function Display
5 meters cable
BALLUFF BNS819-B03-R12-61-12-10
BALLUFF Electromechanical IP67 Multiple Position Switch
BNS819-B03-R12-61-12-10
2 x M20 x 1.5 Connection
3 x Stainless Steel Roller Plunger
12 mm plunger spacing
BALLUFF MICROPULSE Transducer BTL5-A11-M0130-P-S32
BALLUFF MICROPULSE Transducer
Model BTL5-A11-M0130-P-S32
Output Signal :
Analog 0...10V and 10...0V
Supply Voltage :
24 VDC +/- 20%
Load Current :
5mA max.
Max. Ripple :
<5mV
Input Interface :
Analog
Operating Temperature :
-40 ... +85degC
Connection Type :
Connector
Mounting :
Compression Clamp
Housing Material :
Al Anodized
Vibration :
12g, 10...2000 Hz
Repeatability :
Resolution / min. 2 um
Hysteresis:
<4um
Sampling Rate :
1 kHz
System Resolution:
<0.1mV
Nominal Stroke :
130 mm
BALLUFF MICROPULSE Transducer BTL5-E17-M0300-K-SR32
BALLUFF MICROPULSE Transducer
Model BTL5-E7-M0300-K-SR32
Compact Rod Series K
Stainless Steel Material
Output Current :
4-20 mA
Load Resistance :
< 500 Ohm
System Resolution :
< 0.2 uA
Supply Voltage :
20 - 28 VDC
Output Signal :
Analog ( Falling )
Nominal Stroke :
300 mm
Connection Type :
Radial SR32 Connector
BANNER MINI-ARRAY BMEL4216A - BMRL4216A
BANNER Measuring Light Screen System
MINI-ARRAY BMEL4216A ( Emitter ) - BMRL4216A ( Receiver )
Programmable measuring light screen system
Ideally suited for inspection and profiling application
It excel at on the fly product sizing and profiling, edge-guiding and center-guiding, loop tension control. hole detection, die injection verification and similar uses
Each system consists of a controller module, an emitter and receiver, and two interconnecting cable
Programming is accomplished via the controller's built-in serial interface using PC compatible computer
BANNER U-GAGE S18UBAR
BANNER Ultrasonic Sensor
U-GAGE S18UBAR
18 mm Ultrasonic Sensor with TECH-Mode Programming
30 - 300mm Sensing Range
Discrete Output
NO/NC - PNP/NPN
10...30VDC
5 wires - 2 meters cable